龙盛官方论坛
正在验证会员信息...
sheet extruding machine,cup making machine,vacuum forming machine,cup printing machine,straw machine,plastic granulator,coiling machine,punching machine,crusher,cup stacking machine
立式、卧式、斜式、斜卧式四种三辊XBZD100/70-900斜式多层共挤片材机组
今日发帖数: 0|昨日发帖数: 0|帖子数: 2107|会员数: 200
版主: -
回复数量: 1
发表回复 发表主题
查看: 1969 | 回复: 1
管理员 shiela
等级:
上将
发帖:
387/233
积分:
35636
经验值:
235588
上次发言:
04-24 21:22
收藏(0)减速机(波箱)的保养方法

不同的润滑油禁止相互混合使用。油位螺塞、放油螺塞和通气器的位置由安装位置决定。它们的相关位置可参考减速机的安装位置图来确定。

减速机的保养方法

一、油位的检查

  •   切断电源,防止触电!等待减速机冷却!

      移去油位螺塞检查油是否充满。

      安装油位螺塞。

    END

二、油的检查

  •   切断电源,防止触电!等待减速机冷却!

      打开放油螺塞,取油样。

      检查油的粘度指数

      ——如果油明显浑浊,建议尽快更换。

      对于带油位螺塞的减速机

      ——检查油位,是否合格

        ——安装油位螺塞

    END

油的更换

  •   冷却后油的粘度增大放油困难,减速机应在运行温度下换油。

      切断电源,防止触电!等待减速机冷却下来无燃烧危险为止!

      注意:换油时减速机仍应保持温热。

      在放油螺塞下面放一个接油盘。

      减速器打开油位螺塞、通气器和放油螺塞。

      将油全部排除。

      装上放油螺塞。

      注入同牌号的新油。

      油量应与安装位置一致。

      在油位螺塞处检查油位。

      拧紧油位螺塞及通气器。

    减速机的保养方法

送花(0)臭鸡蛋(0)引用回复2013-12-31 15:36 [1楼]
会员 Tina123
等级:
上等兵
发帖:
4/83
积分:
208
经验值:
208
上次发言:
05-14 14:43

1. Check oil level

Cut off the power to prevent electric shock!

Wait for the reducer to cool down!

Remove the oil level screw plug to check whether the oil is full.

Install oil level screw plug.

 

 

2.Second, oil inspection

Cut off the power to prevent electric shock!

Wait for the reducer to cool down!

Open oil screw plug and take oil sample.

Check oil viscosity index

If the oil is obviously cloudy, it is recommended to replace it as soon as possible.

For reducer with oil level screw plug

-- check the oil level to see whether it is qualified

Install oil level screw plug

 

 

Oil change

It is difficult to drain oil when the oil viscosity increases after cooling. The reducer should change oil at the operating temperature.

Cut off the power to prevent electric shock!

Wait until the reducer cools down without burning danger!

Note: the reducer should remain warm during oil change.

Put an oil pan under the drain plug.

The reducer opens the oil level plug, ventilator and drain plug.

Remove all oil.

Install oil drain screw plug.

Inject new oil of the same brand.

The amount of oil should be consistent with the installation position.

Check oil level at oil level plug.

Tighten oil level screw plug and ventilator.

送花(0)臭鸡蛋(0)引用回复2019-07-25 13:51 [2楼]
回复: 1
发表回复
您需要 登录注册 后才可以回帖